Humus Jardin

Have you looked at the spark plugs to see if they need to be changed? Also, with the cam pulley that wobbles, check to make sure the timing marks on both cam pulleys and the crank pulley are aligned with the timing belt. If these marks are off, it can cause BIG problems along with not starting. If the marks are not aligned, align them and then tighten down the pulley and give it a shot.

No crank, no start, no power

If they are aligned, tighten the pulley and give it a shot. I would check the timing before i would check the plugs just because its a little easier. If ur car is off timing, in general, ur check engine light be on and it would idle rough. My suggestion is to eliminate the exhaust being plugged, vaiyo.io disconnect the exhaust manifold at the point that it bolts to the down pipe. Either lossen it up enough where u can see a good size gap or completly unmount it but make sure that down pipe is not going to be swinging around. Then take it on a test drive and see if it makes a difference.

• If the marks are not aligned, align them and then tighten down the pulley and give it a shot.
• I had the same problem and smelled gas after hard acceleration.
• My suggestion is to eliminate the exhaust being plugged, disconnect the exhaust manifold at the point that it bolts to the down pipe.
• It’s some strong stuff bro but even Mama and Brooke can tell when I put it in there cars.
• If ur car is off timing, in general, ur check engine light be on and it would idle rough.
• If you dont really have experience working on cars, imo i would have someone else switch cam pulleys and put everything back to TDC.

CarGurus Experts

It’s some strong stuff bro but even Mama and Brooke can tell when I put it in there cars.

No crank, no start, no power

If the mechanic looked at it and said your timing was off, why wouldnt you just have them do it?? If you dont really have experience working on cars, imo i would have someone else switch cam pulleys and put everything back to TDC. I had the same problem and smelled gas after hard acceleration. Had poor fuel economy accompanying all this with an idle of about 1000rpm sometimes 1100 after warm up. Try putting 2 or 3 bottles of « Lucas Fuel Injector Cleaner » in there. If always peps any of our cars up and the run it almost to empty, I guarantee you’ll notice a difference.

• My suggestion is to eliminate the exhaust being plugged, disconnect the exhaust manifold at the point that it bolts to the down pipe.
• I had the same problem and smelled gas after hard acceleration.
• If these marks are off, it can cause BIG problems along with not starting.
• Either lossen it up enough where u can see a good size gap or completly unmount it but make sure that down pipe is not going to be swinging around.
• If the marks are not aligned, align them and then tighten down the pulley and give it a shot.
• It’s some strong stuff bro but even Mama and Brooke can tell when I put it in there cars.
• If you dont really have experience working on cars, imo i would have someone else switch cam pulleys and put everything back to TDC.

CarGurus Experts

CarGurus Experts

No crank, no start, no power

CarGurus Experts

No crank, no start, no power

No crank, no start, no power

No crank, no start, no power

• Had poor fuel economy accompanying all this with an idle of about 1000rpm sometimes 1100 after warm up.
• If these marks are off, it can cause BIG problems along with not starting.
• Have you looked at the spark plugs to see if they need to be changed?
• Try putting 2 or 3 bottles of « Lucas Fuel Injector Cleaner » in there.
• If the mechanic looked at it and said your timing was off, why wouldnt you just have them do it??
• It’s some strong stuff bro but even Mama and Brooke can tell when I put it in there cars.
• I had the same problem and smelled gas after hard acceleration.

CarGurus Experts

No crank, no start, no power

• I had the same problem and smelled gas after hard acceleration.
• My suggestion is to eliminate the exhaust being plugged, disconnect the exhaust manifold at the point that it bolts to the down pipe.
• I would check the timing before i would check the plugs just because its a little easier.
• If they are aligned, tighten the pulley and give it a shot.
• If the marks are not aligned, align them and then tighten down the pulley and give it a shot.
• If these marks are off, it can cause BIG problems along with not starting.
• Try putting 2 or 3 bottles of « Lucas Fuel Injector Cleaner » in there.
• Either lossen it up enough where u can see a good size gap or completly unmount it but make sure that down pipe is not going to be swinging around.
• If you dont really have experience working on cars, imo i would have someone else switch cam pulleys and put everything back to TDC.
• It’s some strong stuff bro but even Mama and Brooke can tell when I put it in there cars.